Messages

1

Technical Support / Re: Pilotaware FX and Aircrew instrument

« on: November 27, 2024, 09:42:18 pm »

Many thanks Chris

2

Technical Support / Pilotaware FX and Aircrew instrument

« on: November 26, 2024, 05:57:24 pm »

Hi Lee, just wondering if the Aircrew instrument will connect to Pilotaware FX as it does to Rosetta. ie via blue tooth etc
Regards Dave

3

General Discussion / Aircrew connection to FX

« on: November 23, 2024, 01:48:53 pm »

Has anyone used the aircrew instrument with Pilotaware FX. Do they work OK with each other and which is the best way to connect them to each other.

4

Technical Support / Re: Anker recommended Power Supply... doesn't work

« on: November 09, 2023, 07:30:06 pm »

I’m assuming you’ve checked the cable,but I’ve found the power socket on tha Rosetta can be suspect at times especially if the unit is disconnected often from the power lead.

5

Technical Support / Re: Saving radar screen settings

« on: November 02, 2023, 09:54:52 pm »

I’ve checked the browser (Safari) cookies setting and it is not disabled. But my radar settings are not saved. There doesn’t seem to be an answer to the problem

6

Technical Support / Saving radar screen settings

« on: September 25, 2023, 12:05:54 pm »

Is it possible to save the Radar screen settings, or keeping the same vertical and horizontal settings. I t always resets to 26nm and 50000ft. I’ve tried using the save option in the config menu but this doesn’t save the radar screen settings. I’m using igrid for my radar screen. Any help greatly appreciated
Dave

7

Technical Support / Re: Voltage error message on iphone

« on: September 17, 2023, 06:23:10 pm »

I’m using Rosetta. The following in the USB ports : dongle, GPS, aircrew, and Wi-Fi. The PAW is powered from the 12 volt cigarette lighter using an Anker QC adapter. Even with the voltage error message on the iPhone the radar screen seems to be giving me all the info it’s supposed to and generally works very well

8

Technical Support / Voltage error message on iphone

« on: September 17, 2023, 02:45:11 pm »

I’m getting a Voltage error message on iPhone, while using it as hotspot for the radar screen/ I grid.
Everything is green on the Pilotaware Home Screen except red showing voltage error. However the radar screen seems to work very well with all the targets showing and any rain in the vicinity visible.
Also I can get the met and aircraft info up when needed. Any thoughts from the experts out there much appreciated

9

Technical Support / Re: GSM box showing red

« on: December 04, 2022, 04:23:40 pm »

I had a similar issue. I was using an iPhone8 and SkyDemon. I switched off VPN on my iPhone and all worked with no problem. Hope this might help if you check your VPN settings

10

Technical Support / Re: Network Settings page not showing the GRID part

« on: August 08, 2022, 08:35:22 pm »

I think the other is your Pilotaware Wi-Fi!

11

Technical Support / Re: Antennas - where have you stuck yours?

« on: July 29, 2022, 06:00:09 pm »

Hi In my PA28 the antenna are mounted remotely internally. I attach my polar diagram for you to compare. Obviously it depends on how many flights etc. I don’t think mine is the best result but acceptable.

12

Technical Support / Re: iGrid connection to hotspot flakey as hell. - An Update

« on: July 12, 2022, 03:49:39 pm »

Hi All,
Just read admin latest post. That’s just what happens with my IPhone 8. The phone has to be on the hotspot page, then no problems.

Dave

13

Technical Support / Re: Aircrew Instrument Firmware Update

« on: July 09, 2022, 09:31:31 pm »

Hi Peter, Thanks for your reply to the magenta line. Much appreciated.
Dave

14

Technical Support / Re: Aircrew Instrument Firmware Update

« on: July 05, 2022, 10:00:01 pm »

Hi Peter, Thanks for your reply. It’s not a major problem but you wouldn’t notice it unless you zoomed out. It’s not just mine but also my friends system also.
Regards Davd

15

Technical Support / Re: Aircrew Instrument Firmware Update

« on: July 05, 2022, 08:27:51 pm »

Hi All, A couple of us at my home airfield have had a magenta line appear on the aircrew instrument since we’ve updated the latest software version. It only appears when we zoom out to above about 10 miles. It appears from the side of the screen and bears no resemblance to our heading/track. Just  wondering if any one else has experienced this. It doesn’t really worry us since we usually have the scale set to 6/8 miles.
Thanks for your comments
Davd