Show Posts

You can view here all posts made by this member. Note that you can only see posts made in areas to which you currently have access.


Messages - DY691

Pages: [1] 2 3
1
OGN-R PilotAware / Re: FLARM to change protocol
« on: March 27, 2024, 06:24:22 pm »
Good evening
I fly in France and unfortunately there are very few ATOM stations, if any at all...
I think that the flarm signals are recovered via the OGN by the network of my GSM and transmitted by rs232 and wifi to the Dynon and aircrew screens.
In the last few days these signals have disappeared from the Rosetta, hence my question.

2
OGN-R PilotAware / Re: FLARM to change protocol
« on: March 26, 2024, 04:35:21 pm »
Good evening
Is it possible to have an idea of how long it will take for the flarms to reappear on rosetta?
my latest version is 20230316 maybe I forgot to update...
Bonne soirée

3
OGN-R PilotAware / Re: FLARM to change protocol
« on: March 21, 2024, 10:21:55 pm »
By safesky directly

4
OGN-R PilotAware / Re: FLARM to change protocol
« on: March 21, 2024, 10:19:34 am »
Hello
during my last flight in France the flarms were not visible although I activated the connection sharing as before.
Has anything changed?
gliders were available with safesky

5
Technical Support / Re: Status Volt error
« on: May 15, 2023, 12:22:29 pm »
Thanks for the address
I haven't noticed anything else, everything is working normally, just a few restarts of the Rosetta in the air, probably due to the voltage problems.
I will contact you by email at support
Guy

6
Technical Support / Re: Status Volt error
« on: May 15, 2023, 10:54:44 am »
Thanks for the advice
I've checked the motherboard but I didn't see anything obvious...
Is there an email for pilotaware service?

7
Technical Support / Re: Status Volt error
« on: May 12, 2023, 01:38:01 pm »
Photos reosetta

8
Technical Support / Re: Status Volt error
« on: May 12, 2023, 01:26:12 pm »
Hello

On my Rosetta
port 1 wifi key
Port 2 rs232 usb cable to the Dynon HDX
Port 3 GPS
Port 4 nano2
Power supply juicebitz cable 1.8 m

On my friend's Rosetta

Port 1 GPS
Port 2 empty
Port 3 wifi key
Port 4 nano 2

Power supply same juicebitz cable 1.8m

The tests are done with the same PNY battery power supply see the picture

The result is identical with the 2 Rosettas in my machine volt error on my Rosetta ...erratically from time to time I do not have the volt error alarm on my Rosetta but even when the error is present I receive the traffic identically.

The only difference is the presence on my set of the Rs 232 cable .but even when I remove the usb rs 232 cable the volt error alarm still occurs even after a reboot of the Rosetta....

9
Technical Support / Re: Status Volt error
« on: May 10, 2023, 07:53:11 pm »
Tanks foryour message I try to make some picture With the 2 Rosetta tomorow

10
Technical Support / Status Volt error
« on: May 10, 2023, 10:44:19 am »
Hello
I have a small problem with my Rosetta, it is mounted in my plane and when I go on the status page the voltage appears red with volt error indicated.
The information appears on the Dynon HDX screen connected in rs232 as well as on the air Crew connected in wifi.
I plugged in a friend's Rosetta instead of mine and the status is green.
I used the same power supply from my aeroplane 12v cigarette lighter Anker the same cables, the same phenomenon occurs with a battery power supply as well as on a usb plug in my car ...
I have opened the Rosetta cover to see if the power plug is in place and it seems to be ok.
Maybe it's from the motherboard?
If you have any idea?
Thanks for your help and have a nice day.

11
French Specific Forum / Re: Bienvenue
« on: November 14, 2022, 10:51:11 am »
petite précision pour une connexion efficace je suis obligé de choisir dans données cellulaires, options ,le mode faibles de données...sur iphone X

12
French Specific Forum / Re: Bienvenue
« on: September 24, 2022, 12:27:59 pm »
En complément pas d’utilisation possible sur l’écran de l’iPhone X de la fonction affichage de la page radar du Rosetta
cela fonctionne correctement sur un iPad connecté en wifi sur le réseau du Rosetta , cela fonctionne également avec les affichages adsb et flarms sur l’iPad à travers le logiciel EasyVFR 4.

13
French Specific Forum / Re: Bienvenue
« on: September 24, 2022, 12:14:38 pm »
Rapide retour suite à l’installation de la clé wifi disponible avec la dernière version du Rosetta.
Le partage de connexion se fait à partir d’un iPhone X il faut lors de la mise en route du Rosetta laisser la page partage de connexion de l’iPhone ouverte, puis la partie gsm fait son travail avec un transfert des trafics vers l ´Aircrew en wifi et surprise également vers le Dynon …
J’ai fait un À/R Vers Gap a 8000 ft avec un réseau téléphonique disponible 80% du temps les flarms étaient bien reçu via le réseau ogn dans ce laps de temps.

14
Thanks again for your help
I'm going to try this set up but not for another 10 days, I'm getting my daughter married this weekend  :) and back home next week
I'll keep you posted on the rest
Best regards
Guy

15
Thanks Steveu
For your help, I fly in France where we do not have ground stations to receive the flarms, I take advantage of the fact that the trx 1500 has a flarm module to receive it on the Aircrew module...
I actually used the port 2 of the trx via the DB15 plug to the rj45 plug using pins 5 and 6.
I did not connect pin 7, the trx is powered by the Rosetta, maybe I should connect it anyway?





Pages: [1] 2 3