1
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 28, 2019, 09:29:41 pm »
now all working adsb out
Show Posts
You can view here all posts made by this member. Note that you can only see posts made in areas to which you currently have access.
Pages: [1]
2
Technical Support / Re: Is there anyone in Lincolnshire with pilotaware
« on: October 27, 2019, 10:40:10 pm »
Thanks Gerry now sorted
3
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 26, 2019, 08:50:02 am »
Thanks peter
4
Technical Support / Is there anyone in Lincolnshire with pilotaware
« on: October 25, 2019, 09:18:39 pm »
I will be testing my adsb out installation this weekend I need someone with pilotaware to check there traffic with the pc and screen shot it for me to show it’s working thanks all
5
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 25, 2019, 06:21:48 pm »
Also just to say you need to connect a switch to j8 pin 2 so you can disable in case you are testing other things in the hangar etc in case you don’t get gps in your hangar or the transponder will return failure I need to get a print out of someone’s traffic near me for caa mod 7 application thanks
6
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 25, 2019, 05:40:39 pm »
I’ve now got it all installed and just need the weather to try it hopefully tomorrow weather permitting if not Sunday is anyone near Sturgate with a pilot aware to check the traffic to find me on it so I can check for the adsb output thanks
7
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 07:42:55 pm »
Yes I’m using issue 5 and I’m sure I have to select parallel in the ins on the Becker with the 232 connected to pin 8and 9 if I configure the usb to gps I get failure on the Becker but if I select trig it’s fine but I haven’t been able to test if this is working correctly as I don’t have another spare pilot aware to check while I’m out Flying I am speaking to gerhard from Becker tomorrow so hope he shines more light on this thanks for your input
8
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 06:09:14 pm »
But the second diagram shows gps connected to p9 and pin 2 on j8 grounded to enable the gps
9
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 04:20:18 pm »
sorry this is the schematic other one is for a serial encoder attached to j8
10
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 04:10:46 pm »
this is the diagram Im using as im using a parallel encoder p9 pins 8 and 9 and j2 pin 2 ground
11
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 03:04:16 pm »
My blind encoder connected to the Becker bxp6401 is an ak 350 ameri king I tried to upload the schematic but file to big from my phone in the Becker manual 03 issue 05 page 40
12
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 01:37:29 pm »
According to Becker schematic I just connect the 232 to pins 8 and 9 in the p9 connector
13
Technical Support / Re: Becker bxp6401 and adsb out
« on: October 24, 2019, 09:51:58 am »
I’ve seen the posts thanks my transponder is new this year serial number good and software good I think the ones that have posted are using a serial encoder looking at the wiring pin outs they are saying to use I’m using a parallel encoder I will contact Becker tomorrow when there technical is back in thanks
14
Technical Support / Becker bxp6401 and adsb out
« on: October 23, 2019, 08:04:56 pm »
I’ve seen some post for connecting paw to the Becker but I think most have used a serial encoder and ground pin 2 in the p9 plug I have a parallel encoder plugged into p9 and pin 2 is a encoder line for me anyone got this working yet with the output results to show it working
Pages: [1]