Messages

1

General Discussion / Re: SOLVED - Connecting Pilot Aware to SkyView

« on: February 06, 2023, 08:36:51 am »

Thanks Paul, I am doing the same (HDX upgrade). Thanks for your advice. I asked because in the OP is says:

> Configure the USB port on the Pilot Aware to output FLARM traffic and set it to 57600 baud.

I was wondering whether this wouldn't conflict with the settings required to supply to SkyDemon. So thanks for your confirmation that this is not the case.

From my reading I confirm all your other remarks regarding filtering on PAW, and your understanding of HDX' traffic treatment.

2

General Discussion / Re: SOLVED - Connecting Pilot Aware to SkyView

« on: February 05, 2023, 01:12:54 pm »

Is it possible to hard-wire connect PAW Rosetta to Dynon HDX (as described here) AND to at the same time connect the same Rosetta unit to SkyDemon via Wi-Fi?

Or are the PAW settings mutually exclusive.

3

Technical Support / Re: Is it OK to power up Rosetta with no Antennas connected?

« on: November 20, 2022, 07:29:57 pm »

I am running version 20220805. Checking on the configuration I found that Aircraft Type = Base Station is no longer available in the pull down menu for this field.

Is that correct?

4

Technical Support / Re: 20220101 not avail for download?

« on: January 04, 2022, 08:27:08 pm »

Thank you, this time round it worked. Appreciate the newly designed html interface in 20220101.

5

Technical Support / Re: 20220101 not avail for download?

« on: January 04, 2022, 04:07:23 pm »

Hi Ashley

I had done so before posting here (based on information from your knowledgeware webpage). To no avail. After delete app, and download/install again, the app version still was v1.75, and the same story about Nov 2020 being the current version.

On the Apple AppStore, it doesn't give a version history for Firmware Updater? What is the current version (of PAW Firmware Update) that I should be looking out for? Is that current version released world-wide (ie, avail on all local App Stores)?

6

Technical Support / 20220101 not avail for download?

« on: January 03, 2022, 06:56:50 pm »

Alerted by a notification I was wanting to update, using PAW Firmware Updater (v1.75) on the iPad. The Firmware Updater however insisted that I am up-to-date already (with the N0v 2020) release, and that there was not newer version available.

What could be the problem?

7

Technical Support / Re: PAW SkyDemon Connection Problem Coinciding with PAW 201906 update

« on: July 22, 2019, 08:14:06 pm »

  Hi Lee, this seems to fix my problem. The messages not only seem to be confusing Android but also iOS, which is what I am using.

This "Device Connector Setting" on the config page seems to be new with 20190621, that's maybe how I missed it when copying over the config settings after the software upgrade.

Connect to SD now works as instantaneous as it used to. I will obviously have to test further but at the office it works fine!

8

Technical Support / SOLVED: PAW SkyDemon Connection Problem Coinciding with PAW 201906 update

« on: July 22, 2019, 05:58:24 pm »

I am using the Rosetta since May 2019. Everything was working fine until the day of the (otherwise uneventful and successful) PAW 201906 software upgrade. Now I have often have persistent problems connecting PAW to SD. I am using SD in parallel on two ipads. I have the problems with both ipads. Sometimes with both iPads at the same time, but mostly on the newer iPad only, while it connects OK to the elder iPad.
 
The problem seems to coincide with the upgrade to the new PAW 201906 version, and/or the latest SD version.

Even, if things are working, I noticed the following changes:
 
- When Go Flying and Use PAW, the connection is not as instantaneous as it used to be.
- If SD can see the PAW connection, it states a green bar with  “Connecting to Devise”, then “GPS Signal Lost – 7 Found” (or similar number, like “8 Found”), then connects after a another second or two.
 
Now, if SD cannot see the connection, it states a green bar with “Connecting to Device”, then after 5 to 10 sec it comes with another white window, stating “No data has been received from your GPS devise for some time …”, and reverts to planning mode.
 
All the while the same iPad can (without exception) access PAW via browser at 192.168.1.1, and gets all good, four green indicators on all that matters.
 
What I found interesting is that in this 192.168.1.1 browser window, under “Clients” tab – if the SD cannot see PAW – the Hostname of that iPad is not “Tims ipad” (or similar) but stated as “GDL90”. When by hook or by crook I eventually get it to connect, only then the Hostname changes to "Tims iPad".

Does anybody else has the same problem?

9

Technical Support / Re: Anker powercore 20100 problem?

« on: July 22, 2019, 05:45:46 pm »

I bought the Anker Powercore 20100 end of April 2019 from Amazon (in California, USA). I connect the Rosetta via a Raysun 90 deg Micro USB Male to USB 2.0 A Male short cable (also available form Amazon).

It works 100% without any problems. The 20100 comes alive immediately when I put the USB connector in, even if no other consumer is connected to the power bank.

The width of the 20100 is equal to the width of Rosetta. And the length of the Rosetta (overall incl aerials) is about the same as the power bank. I taped the Rosetta on top of the power bank, with the aerials at the same side as the status LED's of the 20100 (status LED's hence visible at all times). I couldn't think of an aesthetically or practically more pleasing solution.