OGN PAW up link do not see PAW trafic ( resolved )

[Andrzej]

part 1

[Andrzej]

part 2

[Andrzej]

part 3 when i switch off PAW classic

[Admin]

Hi Anrzej

Very strange
As you can see, your paw is being picked up, it is reported in the log
The problem is that the base station thinks it is 6100 km away, so is an error

I think what is happening is that your receiver is located at lat 0.0, lon 0.0
The position of the receiver should be determined after less than 10 mins,
I capture the outgoing message to the ogn, and use this info, I think
Something is going wrong at that point

I cannot investigate fully until Friday as I am away on vacation

Thx
Lee

[exfirepro]

Andrzej,

I take it you reconfigured your OGN software properly after re-installing it on your reformatted card?

You can check the configuration screen manually from the Pi login screen...

pi@ognpaw ~$ cd rtlsdr-ogn

sudo /root/mount_rw.bash

Then... sudo nano rtlsdr-ogn-paw.conf

Check and if necessary correct your Lat and Long settings manually. (a before and after screengrab will confirm your settings.)

'Ctrl O' then Enter to save the changes, then 'Ctrl X' to exit the .conf file

sudo /root/mount_ro.bash Enter to write protect the file

sudo reboot Enter to restart the unit.

Worth a try! Worst case scenario you need to start again with a new software install.

Regards

Peter

[Andrzej]

Peter

I was perform new instalation , new SD card w fev times  with first bridge and new bridge -  no change . I will try Yours way ...

But look for picture ...Like Lee sugestion very strange ,,, all looks good but is something what maybe i do wrong and cant see that .

I am waiting for new PI board 

Other thinks i am thinking that maybe my ruter blocks some trafic to OGN ... "DDB   0" ...

BR
Andrzej 

[Admin]

Hi Andrzej

I think its a software bug, it looks like the PAW receiver software cannot determine the location

Thx
Lee

[Admin]

Hi Andrzej

are you using any special characters in your station name ?
I notice that the name for your station (in Polish) could use the special 'e' character.

Please confirm the characters are standard 8bit ASCII names.
Could you also try a test of naming your station
PAWTEST

edit:
Actually now looking at the messages you reported, I think this could be the issue, looks like in the name you are using an extended ascii character, this would affect the message parsing.

Thx
Lee

[Andrzej]

Hi Lee
I am sure that i use name with standard ...PRZESOC  i do not use ĆÇ ĘÄ   etc !!   I will  check and change it fo your sugestion aprox 21.00 LT ..
BR Andrzej

[Admin]

Hi Andrzej

The issue is an APRS Parsing bug, I have reproduced your issue, I am looking at a fix

edit: Uploaded a Fix

Thx
Lee

[Andrzej]

Hi to All
Problem solved , THX a lot Lee for fast killing a bug ..
I downloaded a new software from server  and my PAW Classic is visible  by OGN system
So  i will soon install a station on EPSD now name is PWTEST
http://ognrange.onglide.com/#PWPWTEST,max,all,53.549716_14.551694,10,#000000ff:#000000ff,circles;

Best Regards
Andrzej
Poland

[exfirepro]

Lee,

Is this bug in the PAW or the OGN-R software? Do we all need to replace our existing?

Regards

Peter

[Admin]

Lee,
Is this bug in the PAW or the OGN-R software? Do we all need to replace our existing?
Regards
Peter

  only if you are East of the Greenwich Mean Line
It was a silly parsing error of Easterly co-ordinates for the Ground Station location

I will be putting up a new release today, which will report to Glidernet which version of Software is being run by the groundstation, this will help in diagnosing any problems, it will appear like this :-

14580    PWCoventr    80.6.96.170:33530    Yes    3m    3m    OGN-R/PilotAware 20170826    0    0/0/0    929    71    4.3 / 0    0    0    g/ALL

I will also post details of an incremental update, which means you simply type a command - and all is done, no recalibration, full install etc


thx
Lee

[Admin]

Update Instructions Topic

http://forum.pilotaware.com/index.php/topic,1012.0.html

Thx
Lee

[scsirob]

For what it's worth, I'm running pretty much the same setup as Andrzej, and it does work OK for me. My version does not run 0.2.6 though, it's 0.2.5?

Version 20170830 : Date 2017-09-09 12:44:48 : Station PWHLaken
P3I Packets OK=152778 NG=0
ICAO    Type    Dist(KM)    Alt(FT)    Uplink
4845C4    PAW    0.01    0    -